Tyan S5211G2NR Datový list

1 http://www.tyan.com Toledo i3210W Toledo i3200R /// S5211 S5211-1U Version 1.4 Copyright Copyright © 2009 MiTAC International Corporation

10 http://www.tyan.com 2.2 - Block Diagram NOTE: If a PCI-E x16 VGA adapter is inserted into PCI-E slots, the VGA card will only work at PCI-E x1 sp

11 http://www.tyan.com NOTE: If a PCI-E x16 VGA adapter is inserted into PCI-E slot, the VGA card will only work at PCI-E x1 speed; this is a chips

12 http://www.tyan.com 2.3 - Board Parts, Jumpers and Connectors This diagram is representative of the latest board revision available at the time

13 http://www.tyan.com Jumper/Connector Function COM2 (J19) COM2 Header FAN1/2/3/4/5/6 4-pin Fan Connector USB1 (JP7) / USB2 (JP2) USB Front Pane

14 http://www.tyan.com FAN1TYFP1FAN2FAN3 FAN6FAN4TYFP2 FAN5

15 http://www.tyan.com FAN1/2/3/4/5/6/: 4-pin Fan Connector 4-pin Fan +12VSpeed ControlGNDTachometer1 Use these headers to connect the 4-pin cooli

16 http://www.tyan.com COM2IPMB USB2USB1J10 J23

17 http://www.tyan.com USB1 (JP7) / USB2 (JP2): USB Front Panel Connector 1 92 1 0 Pin Signal Pin S

18 http://www.tyan.com JP4J24SATA3SATA4SATA2SATA1SATA5SATA0CMOS

19 http://www.tyan.com J24: Barebone Fan Connector (reserved for OEM only) 121314 Pin Signal Pin Signal 1 FAN1_TACH 2 FAN6_TACH3 FAN2_TACH 4 Rese

2 http://www.tyan.com Table of Contents Check the box contents! 3Chapter 1: Introduction 1.1 Congratulations 51.2 Hardware Specification

20 http://www.tyan.com 2.4 - Tips on Installing Motherboard in Chassis Before installing your motherboard, make sure your chassis has the necessary

21 http://www.tyan.com 2.5 - Installing the Memory Before installing memory, ensure that the memory you have is compatible with the motherboard and p

22 http://www.tyan.com Refer to the following table for supported DDRII populations. (Note: X indicates a populated DIMM slot) Channel A Channel B

23 http://www.tyan.com Memory Installation Procedure Follow these instructions to install memory modules into the S5211/S5211-1U. 1. Press the locki

24 http://www.tyan.com 2.6 - Installing the Processor and Cooling Fan Your S5211/S5211-1U supports the latest processor technologies from Intel. Che

25 http://www.tyan.com 4. Remove the PnP cap from the load plate. 5. Replace the load plate and return the locking lever to the locking position.

26 http://www.tyan.com 2. Turn the board upside down and insert the heat sink spring mechanism as shown. 3. Align the heatsink with the four hole

27 http://www.tyan.com 2.7 - Attaching Drive Cables Attaching IDE Drive Cable Attaching the IDE drive cable is simple. These cables are “keyed” to

28 http://www.tyan.com The following pictures illustrate how to connect an SATA drive 1. SATA drive cable connection 2. SATA drive power connecti

29 http://www.tyan.com 2.9 - Installing Optional SO-DIMM modules Your S5211/S5211-1U motherboard is equipped with an optional proprietary SO-DIMM co

3 http://www.tyan.com Check the box contents! 1x S5211/S5211-1U motherboard 1 x Ultra-DMA-133/100/66/33 IDE cable 6 x Serial ATA cables 1 x USB2.

30 http://www.tyan.com 2.10 - Connecting External Devices The following diagram will detail the rear port stack for this S5211/S5211-1U motherboard:

31 http://www.tyan.com 2.11 - Installing the Power Supply There are two power connectors on your mainboard. The board requires that you use an EPS12

32 http://www.tyan.com NOTE

33 http://www.tyan.com Chapter 3: BIOS Setup 3.1 About the BIOS The BIOS is the basic input/output system, the firmware on the motherboard that ena

34 http://www.tyan.com Getting Help Pressing [F1] displays a small help window that describes the appropriate keys to use and the possible selections

35 http://www.tyan.com 3.2 Main BIOS Setup When you enter PhoenixBIOS CMOS Setup Utility, the following screen will appear as below: The main menu

36 http://www.tyan.com 3.3 Main In this section, you can alter general features such as the date and time, as well as access to the IDE configuration

37 http://www.tyan.com 3.3.1 SATA Port 1~6 Computer detects the hard disk drive type for each drive. Press [Enter] to view advanced details of the co

38 http://www.tyan.com When LBA is turned on, the BIOS will enable geometry translation. This translation may be done in the same way that it is done

39 http://www.tyan.com 3.3.2 Memory Cache This setting allows you to tweak the various cache settings for optimal performance of your system. Press

4 http://www.tyan.com NOTE

40 http://www.tyan.com program writes into this memory area, it will result in a system crash. So, it is recommended that you write protect this area

41 http://www.tyan.com 3.3.3 Boot Features This setting allows you to tweak the various boot settings for optimal performance of your system. Pres

42 http://www.tyan.com Boot-time Diagnostic Screen This feature is used to display the diagnostic screen during the boot process. Options: Enabled /

43 http://www.tyan.com 3.4 Advanced This section facilitates configuring advanced BIOS options for your system. NOTE: When an IPMI card is instal

44 http://www.tyan.com Large Disk Access Mode This option determines whether a hard drive with more than 1024 cylinders, more than 16 heads and or mo

45 http://www.tyan.com 3.4.1 Advanced Chipset Control This section allows you to fine tune the chipset configuration. Onboard VGA Control It allow

46 http://www.tyan.com ECC Delivery When an ECC error occurs, it generates an interrupt. Select the type of interrupt to report: [NMI Non-maskable],

47 http://www.tyan.com 3.4.1.1 Integrated Device Control Sub-Menu USB Dev #29 Controls the USB device by selecting the listed USB functions. Option

48 http://www.tyan.com 3.4.1.1.1 LAN Control Sub-Menu LAN1 / LAN2 Enables the onboard LAN controller. Options: Enabled / Disabled Option ROM Scan

49 http://www.tyan.com 3.4.1.2 PCI Express Sub-Menu PCI Express Base Address / GMCH Base Address / DMI Base Address / Egress Port Base Address / I

5 http://www.tyan.com Chapter 1: Introduction 1.1 - Congratulations You have purchased one of the most powerful server solutions available. The Tol

50 http://www.tyan.com 3.4.1.2.1 PCI-E1/E2 Sub-Menu PCI Express Graphics Port This feature is used to control the PCI Express Graphics port. Optio

51 http://www.tyan.com 3.4.2 Advanced Processor Options This section allows you to fine-tune the processor options. Hyperthreading Enable this only

52 http://www.tyan.com L3 Cache Enable / Disable CPU L3 Cache. Options: Disabled / Enabled Thermal Management 2 Select between TM1 and TM2. Options:

53 http://www.tyan.com 3.4.3 I/O Device Configuration This setting allows you to configure I/O devices. Serial Port A/B: This defines how the seri

54 http://www.tyan.com 3.4.4 DMI Event Logging This section allows you to fine tune the DMI Event Logging configuration. Event Log Capacity It repo

55 http://www.tyan.com 3.4.5 Hardware Monitor This section allows you to fine tune the Hardware Monitor configuration. Fan1/Fan2/Fan3/Fan4/Fan5/

56 http://www.tyan.com 3.4.5.1 Voltage Monitoring Sub-Menu All items on this submenu can not be modified in user mode. Read only.

57 http://www.tyan.com 3.4.6 IPMI This section allows you to configure the IPMI settings. IPMI Specification Version / BMC Firmware Version It disp

58 http://www.tyan.com BIOS POST Watchdog Select [Disabled] if users don’t want to stop POST with any error. Options: Disabled / Enabled OS Boot Wat

59 http://www.tyan.com 3.4.6.2 System Event Log (list mode) Sub-Menu All items on this submenu can not be modified in user mode. Read only.

6 http://www.tyan.com Integrated SATA II (ICH9R) • Supports six SATA-II ports running at 3.0Gb/s • RAID 0/1/5/10 capable (Windows driver support only)

60 http://www.tyan.com 3.4.6.3 Realtime Sensor Data Sub-Menu All items on this submenu can not be modified in user mode. Read only.

61 http://www.tyan.com 3.4.7 Console Redirection This section allows you to configure the Console Redirection. Com Port Address Selects Com Port on

62 http://www.tyan.com 3.5 Security These settings allow you to configure the security options for your system. Supervisor / User Password Is The sy

63 http://www.tyan.com 3.6 Power Use this screen to select options for the Power Settings Configuration. Resume On Time When enabled, this allows t

64 http://www.tyan.com 3.7 Boot Use this screen to select options for the Boot Settings Configuration. Boot Priority Order It shows the boot priori

65 http://www.tyan.com 3.8 Exit These settings set the exit options on your system. Exit Saving Changes This exits BIOS setup after saving the chan

66 http://www.tyan.com NOTE

67 http://www.tyan.com Chapter 4: Diagnostics Note: if you experience problems with setting up your system, always check the following things in the

68 http://www.tyan.com 4.3 Phoenix BIOS Post Code Code Beeps / Description Code Beeps / Description 02h Verify Real Mode 32h Test CPU bus-cloc

69 http://www.tyan.com Code Beeps / Description Code Beeps / Description system BIOS shadow caches 30h 1-4-1-1. RAM failure on data bits of high

7 http://www.tyan.com Chapter 2: Board Installation You are now ready to install your motherboard. The mounting hole pattern of the Toledo i3210W/i32

70 http://www.tyan.com Code Beeps / Description Code Beeps / Description register 97h Fixup Multi Processor table 80h Chipset Init 98h 1-2.

71 http://www.tyan.com Appendix: SMDC Information Overview TYAN® Server Management Daughter Card (SMDC) is a powerful yet cost-efficient solution f

72 http://www.tyan.com Features of Tyan® Server Management Monitor various system components remotely - such as fans, processor temperature, and m

73 http://www.tyan.com Glossary ACPI (Advanced Configuration and Power Interface): a power management specification that allows the operating system

74 http://www.tyan.com Bus: a data pathway. The term is used especially to refer to the connection between the processor and system memory, and betwe

75 http://www.tyan.com IRQs, it is vital that you do not double up devices on a single line. Plug-n-Play devices will take care of this for you. Doz

76 http://www.tyan.com Enhanced IDEs (EIDEs), with maximum capacity determined by the hardware controller. I/O (Input/Output): the connection betwee

77 http://www.tyan.com PM timers (Power Management timers): software timers that count down the number of seconds or minutes until the system times o

78 http://www.tyan.com design, with cables that are simpler to route and install, smaller cable connectors, and lower voltage requirements. SDRAM (S

79 http://www.tyan.com Technical Support If a problem arises with your system, you should first turn to your dealer for direct support. Your system

8 http://www.tyan.com 2.1- Board Image Toledo i3210W S5211 This picture is representative of the latest board revision available at the time of pu

80 http://www.tyan.com Notice for the USA Compliance Information Statement (Declaration of Conformity Procedure) DoC FCC Part 15: This device compli

9 http://www.tyan.com Toledo i3200R S5211-1U This picture is representative of the latest board revision available at the time of publishing. T